R309-525-11. Chemical Addition  


Latest version.
  • (1) Standards.

    Chemicals used in the treatment of surface water shall achieve the following:

    (a) Primary coagulant chemicals shall be utilized to permit the formation of a floc,

    (b) Disinfectants shall be added to raw and/or treated water.

    (2) Application Criteria.

    In achieving these goals the chemical(s) shall be applied to the water:

    (a) To assure maximum control and flexibility of treatment,

    (b) To assure maximum safety to consumer and operators,

    (c) To prevent backflow or back-siphonage of chemical solutions to finished water systems.

    (d) With appropriate spacing of chemical feed to eliminate any interference between chemicals.

    (3) Typical Chemical Doses.

    Chemical doses shall be estimated for each treatment plant to be designed. "Jar tests" shall be conducted on representative raw water samples to determine anticipated doses.

    (4) Information Required for Review.

    With respect to chemical applications, a submittal for Division review and Director approval shall include:

    (a) Descriptions of feed equipment, including maximum and minimum feed rates,

    (b) Location of feeders, piping layout and points of application,

    (c) Chemical storage and handling facilities,

    (d) Specifications for chemicals to be used,

    (e) Operating and control procedures including proposed application rates,

    (f) Descriptions of testing equipment and procedures, and

    (g) Results of chemical, physical, biological and other tests performed as necessary to define the optimum chemical treatment.

    (5) Quality of Chemicals.

    All chemicals added to water being treated for use in a public water system for human consumption shall comply with ANSI/NSF Standard 60. Evidence for this requirement shall be met if the chemical shipping container labels or material safety data sheets include:

    (a) Chemical name, purity and concentrations, Supplier name and address, and

    (b) Labeling indicating compliance with ANSI/NSF Standard 60.

    (6) Storage, Safe Handling and Ventilation of Chemicals.

    All requirements of the Utah Occupational Safety and Health Act (UOSHA) for storage, safe handling and ventilation of chemicals shall apply to public drinking water facilities. The designer shall incorporate all applicable UOSHA standards into the facility design, however, review of facility plans by the Director under this Rule shall be limited to the following requirements:

    (a) Storage of Chemicals.

    (i) Space shall be provided for:

    (A) An adequate supply of chemicals,

    (B) Convenient and efficient handling of chemicals,

    (C) Dry storage conditions.

    (ii) Storage tanks and pipelines for liquid chemicals shall be specific to the chemicals and not for alternates.

    (iii) Chemicals shall be stored in covered or unopened shipping containers, unless the chemical is transferred into a covered storage unit.

    (iv) Liquid chemical storage tanks must:

    (A) Have a liquid level indicator, and

    (B) Have an overflow and a receiving basin or drain capable of receiving accidental spills or overflows, and meeting all requirements of R309-525-23, and

    (C) Be equipped with an inverted "J" air vent.

    (v) Acids shall be kept in closed acid-resistant shipping containers or storage units.

    (b) Safe Handling.

    (i) Material Safety Data Sheets for all chemicals utilized shall be kept and maintained in prominent display and be easily accessed by operators.

    (ii) Provisions shall be made for disposing of empty bags, drums or barrels by an acceptable procedure which will minimize operator exposure to dusts.

    (iii) Provisions shall be made for measuring quantities of chemicals used to prepare feed solutions.

    (c) Dust Control and Ventilation.

    Adequate provision shall be made for dust control and ventilation.

    (7) Feeder Design, Location and Control.

    (a) General Feeder Design.

    General equipment design, location and control shall be such that:

    (i) feeders shall supply, at all times, the necessary amounts of chemicals at an accurately controlled rate, throughout the anticipated range of feed,

    (ii) chemical-contact materials and surfaces are resistant to the aggressiveness of the chemicals,

    (iii) corrosive chemicals are introduced in a manner to minimize potential for corrosion,

    (iv) chemicals that are incompatible are not fed, stored or handled together.

    (v) all chemicals are conducted from the feeder to the point of application in separate conduits,

    (vi) spare parts are available for all feeders to replace parts which are subject to wear and damage,

    (vii) chemical feeders are as near as practical to the feed point,

    (viii) chemical feeders and pumps operate at no lower than 20 percent of the feed range,

    (ix) chemicals are fed by gravity where practical,

    (x) be readily accessible for servicing, repair, and observation.

    (b) Chemical Feed Equipment.

    Where chemical feed is necessary for the protection of the consumer, such as disinfection, coagulation or other essential processes:

    (i) a minimum of two feeders, one active and one standby, shall be provided for each chemical,

    (ii) the standby unit or a combination of units of sufficient capacity shall be available to replace the largest unit during shut-downs,

    (iii) where a booster pump is required, duplicate equipment shall be provided and, when necessary, standby power,

    (iv) a separate feeder shall be used for each non-compatible chemical applied where a feed pump is required, and

    (v) spare parts shall be available for all feeders to replace parts which are subject to wear and damage.

    (c) Dry Chemical Feeders.

    Dry chemical feeders shall:

    (i) measure feed rate of chemicals volumetrically or gravimetrically, and

    (ii) provide adequate solution water and agitation of the chemical in the solution tank.

    (d) Feed Rate Control.

    (i) Feeders may be manually or automatically controlled, with automatic controls being designed to allow override by manual controls.

    (ii) Chemical feed rates shall be proportional to flows.

    (iii) A means to measure water flow rate shall be provided.

    (iv) Provisions shall be made for measuring the quantities of chemicals used.

    (v) Weighing scales:

    (A) shall be provided for weighing cylinders at all plants using chlorine gas,

    (B) may be required for fluoride solution feed, where applicable,

    (C) shall be provided for volumetric dry chemical feeders, and

    (D) shall be accurate to measure increments of 0.5 percent of scale capacity.

    (8) Feeder Appurtenances.

    (a) Liquid Chemical Solution Pumps.

    Positive displacement type solution feed pumps shall be used to feed liquid chemicals, but shall not be used to feed chemical slurries. Pumps must be sized to match or exceed maximum head conditions found at the point of injection. All liquid chemical feeders shall be provided with devices approved by the Utah Plumbing Code which will prevent the siphoning of liquid chemical through the pump.

    (b) Solution Tanks.

    (i) A means consistent with the nature of the chemical solution shall be provided in a solution tank to maintain a uniform strength of solution. Continuous agitation shall be provided to maintain slurries in suspension.

    (ii) Means shall be provided to measure the solution level in the tank.

    (iii) Chemical solutions shall be kept covered. Large tanks with access openings shall have the openings curbed and fitted with tight overhanging covers.

    (iv) Subsurface locations are discouraged, but when used for solution tanks shall:

    (A) be free from sources of possible contamination, and

    (B) assure positive drainage for ground waters, accumulated water, chemical spills and overflows.

    (v) Overflow pipes, when provided, shall:

    (A) have a free fall discharge, and

    (B) be located where noticeable.

    (vi) Acid storage tanks shall be vented to the outside atmosphere, but not through vents in common with day tanks.

    (vii) Each tank shall be provided with a valved drain, protected against backflow in accordance with R309-525-11(10)(b) and R309-525-11(10)(c).

    (viii) Solution tanks shall be located and protective curbing provided so that chemicals from equipment failure, spillage or accidental drainage shall not enter the water in conduits, treatment or storage basins.

    (ix) When polymers are used, storage tanks shall be located away from heat sources and direct sunlight.

    (c) Day Tanks.

    (i) Day tanks shall be provided where dilution of liquid chemical is required prior to feeding.

    (ii) Day tanks shall meet all the requirements of R309-525-11(9)(b).

    (iii) Certain chemicals, such as polymers, become unstable after hydration, therefore, day tanks shall hold no more than a thirty hour supply unless manufacturer's recommendations allow for longer periods.

    (iv) Day tanks shall be scale-mounted, or have a calibrated gauge painted or mounted on the side if liquid levels cannot be observed in a gauge tube or through translucent sidewalls of the tank. In opaque tanks, a gauge rod extending above a referenced point at the top of the tank, attached to a float may be used. The ratio of the cross-sectional area of the tank to its height must be such that unit readings are meaningful in relation to the total amount of chemical fed during a day.

    (v) Hand pumps may be provided for transfer from a carboy or drum. A top rack may be used to permit withdrawal into a bucket from a spigot. Where motor-driven transfer pumps are provided a liquid level limit switch and an overflow from the day tank, which will drain by gravity back into the bulk storage tank, must be provided, unless spill containment is provided for both bulk and day tanks.

    (vi) A means which is consistent with the nature of the chemical solution shall be provided to maintain uniform strength of solution in a day tank. continuous agitation shall be provided to maintain chemical slurries in suspension.

    (vii) Tanks shall be properly labeled to designate the chemical contained.

    (d) Feed Lines.

    (i) Feed lines shall be as short as possible in length of run, and be:

    (A) of durable, corrosion resistant material,

    (B) easily accessible throughout the entire length,

    (C) protected against freezing, and

    (D) readily cleanable.

    (ii) Feed lines shall slope upward from the chemical source to the feeder when conveying gases.

    (iii) Lines shall be designed with due consideration of scale forming or solids depositing properties of the water, chemical, solution or mixture conveyed.

    (9) Make up Water Supply and Protection.

    (a) In Plant Water Supply.

    In plant water supply shall be:

    (i) Ample in supply, adequate in pressure, and of a quality equal to or better than the water at the point of application.

    (ii) Provided with means for measurement when preparing specific solution concentrations by dilution.

    (iii) Properly protected against backflow.

    (b) Cross-Connection Control.

    Cross-connection control shall be provided to assure that:

    (i) The make-up waterlines discharging to solution tanks shall be properly protected from backflow as required by the Utah Plumbing Code.

    (ii) Liquid chemical solutions cannot be siphoned through solution feeders into the process units as required in R309-525-11(9)(c).

    (iii) No direct connection exists between any sewer and the drain or overflow from the feeder, solution chamber or tank by providing that all pipes terminate at least six inches or two pipe diameters, whichever is greater, above the overflow rim of a receiving sump, conduit or waste receptacle.

    (iv) Pre- and post-chlorination systems must be independent to prevent possible siphoning of partially treated water into the clear well. The water supply to each eductor shall have a separate shut-off valve. No master shut off valve will be allowed.

    (c) Liquid Chemical Feeders, Siphon Control.

    Liquid chemical feeders shall be such that chemical solutions cannot be siphoned into the process units, by:

    (i) Assuring positive pressure at the point of discharge,

    (ii) Providing vacuum relief,

    (iii) Providing a suitable air gap, or

    (iv) Other suitable means or combinations as necessary.

    (10) Operator Safety.

    Design of the plant shall be in accordance with the Utah Occupational Safety and Health Act (UOSHA). The designer and public water system management are responsible to see that they incorporate applicable UOSHA standards into the facility design and operation. Review of facility plans by the Division shall be limited to the following requirements:

    (a) Floor surfaces shall be smooth and impervious, slip-proof and well drained,

    (b) At least one pair of rubber gloves, a dust respirator of a type certified by the National Institute of Occupational Safety and Health (NIOSH) for toxic dusts, an apron or other protective clothing and goggles or face mask should be provided for each operator, A deluge shower and/or eye washing device shall be installed where strong acids and alkalis are used or stored.

    (c) A water holding tank that will allow water to reach room temperature should be installed in the water line feeding the deluge shower and eye washing device. Other methods of water tempering may be available.

    (d) Adequate ventilation should be provided.

    (11) Design for Specific Chemicals.

    Design of the plant shall be in accordance with the Utah Occupational Safety and Health Act (UOSHA). The designer and public water system management are responsible to see that they incorporate applicable UOSHA standards into the facility design and operation. Review of facility plans by the Division shall be limited to the following requirements:

    Acids and Caustics.

    (i) Acids and caustics shall be kept in closed corrosion-resistant shipping containers or storage units.

    (ii) Acids and caustics shall not be handled in open vessels, but shall be pumped in undiluted form from original containers through suitable hose, to the point of treatment or to a covered day tank.

    Sodium Chlorite for Chlorine Dioxide Generation.

    Proposals for the storage and use of sodium chlorite should be approved by the Director prior to the preparation of final plans and specifications. Provisions shall be made for proper storage and handling of sodium chlorite to eliminate any danger of explosion.

    (i) Sodium Chlorite Storage: (A) Sodium chlorite shall be stored by itself in a separate room and preferably should be stored in an outside building detached from the water treatment facility. It shall be stored away from organic materials which would react violently with sodium chlorite; (B) The storage structures shall be constructed of noncombustible materials; (C) If the storage structure is to be located in a area where a fire may occur, water shall be available to keep the sodium chlorite area sufficiently cool to prevent decomposition from heat and resultant potential explosive conditions.

    (ii) Sodium Chlorite Handling: (A) Care should be taken to prevent spillage; (B) An emergency plan of operation shall be available for the clean up of any spillage; (C) Storage drums should be thoroughly flushed prior to recycling or disposal.

    (iii) Sodium Chlorite Feeders: (A) Positive displacement feeders should be provided; (B) Tubing for conveying sodium chlorite or chlorine dioxide solutions shall be Type 1 PVC, polyethylene or materials recommended by the manufacturer; (C) Feed lines shall be installed in a manner to prevent formation of gas pockets and shall terminate at a point of positive pressure; (D) Check valves shall be provided to prevent the backflow of chlorine into the sodium chlorite line.