No. 37336 (Amendment): Rule R315-315. Special Waste Requirements  

  • (Amendment)

    DAR File No.: 37336
    Filed: 02/15/2013 08:49:56 AM

    RULE ANALYSIS

    Purpose of the rule or reason for the change:

    Changes are required to conform with S.B. 21 passed during 2012 General Session (Chapter 360, Laws of Utah 2012).

    Summary of the rule or change:

    S.B. 21, passed during the 2012 General Session, removed some authorities from the Utah Solid and Hazardous Waste Control Board and its Executive Secretary and gave them to the Director of the Division of Solid and Hazardous Waste. This change in statute now requires changes to the Solid and Hazardous Waste rules. Specifically, references to the "Board" and the "Executive Secretary" in the rules need to be changed to "Director" as appropriate.

    State statutory or constitutional authorization for this rule:

    Anticipated cost or savings to:

    the state budget:

    There are no anticipated costs or savings as this amendment only changes who has authority to make regulatory decisions.

    local governments:

    There are no anticipated costs or savings as this amendment only changes who has authority to make regulatory decisions.

    small businesses:

    There are no anticipated costs or savings as this amendment only changes who has authority to make regulatory decisions.

    persons other than small businesses, businesses, or local governmental entities:

    There are no anticipated costs or savings as this amendment only changes who has authority to make regulatory decisions.

    Compliance costs for affected persons:

    There are no compliance costs for affected persons as this amendment only changes who has authority to make regulatory decisions.

    Comments by the department head on the fiscal impact the rule may have on businesses:

    There is no anticipated fiscal impact on businesses as this amendment only changes who has authority to make regulatory decisions.

    Amanda Smith, Executive Director

    The full text of this rule may be inspected, during regular business hours, at the Division of Administrative Rules, or at:

    Environmental Quality
    Solid and Hazardous WasteRoom Second Floor
    195 N 1950 W
    SALT LAKE CITY, UT 84116-3097

    Direct questions regarding this rule to:

    Interested persons may present their views on this rule by submitting written comments to the address above no later than 5:00 p.m. on:

    04/01/2013

    This rule may become effective on:

    04/15/2013

    Authorized by:

    Scott Anderson, Director

    RULE TEXT

    R315. Environmental Quality, Solid and Hazardous Waste.

    R315-315. Special Waste Requirements.

    R315-315-1. General Requirements.

    (1) If special wastes are accepted at the facility, proper provisions shall be made for handling and disposal. These provisions may include, where required and approved by the [Executive Secretary]Director, a separate area for disposal of the wastes, designated by appropriate signs.

    (2) Sections R315-315-2 through 9 are applicable to all solid waste facilities regulated by Rules R315-301 through 320.

     

    R315-315-2. Asbestos Waste.

    (1) Regulated asbestos-containing material to be disposed of shall be handled, transported, and disposed in a manner that will not permit the release of asbestos fibers into the air and must otherwise comply with Code of Federal Regulations, Title 40, Part 61, Section 154.

    (2) No transporter or disposal facility shall accept regulated asbestos-containing material unless the waste has been adequately wetted and containerized.

    (a) Regulated asbestos-containing material is adequately wetted when its moisture content prevents fiber release.

    (b) Regulated asbestos-containing material is properly containerized when it is placed in double plastic bags of 6-mil or thicker, sealed in such a way to be leak-proof and air-tight, and the amount of void space or air in the bags is minimized. Regulated asbestos-containing material slurries must be packaged in leak-proof and air-tight rigid containers if such slurries are too heavy for the plastic bag containers. Upon submittal of a request, including documentation demonstrating safety, the [Executive Secretary]Director may authorize other proper methods of containment which may include double bagging, plastic-lined cardboard containers, plastic-lined metal containers, or the use of vacuum trucks for the transport of slurry.

    (c) All containers holding regulated asbestos-containing material shall be labeled with the name of the waste generator, the location where the waste was generated, and tagged with a warning label indicating that the containers hold regulated asbestos-containing material.

    (3) The following standards apply to the disposal of Regulated Asbestos-Containing Material;

    (a) upon entering the disposal site, the transporter of the regulated asbestos-containing material shall notify the landfill operator that the load contains regulated asbestos-containing material by presenting the waste shipment record. The landfill operator will verify quantities received, sign off on the waste shipment record, and send a copy of the waste shipment record to the generator within 30 days;

    (b) upon receipt of the regulated asbestos-containing material, the landfill operator shall inspect the loads to verify that the regulated asbestos-containing material is properly contained in leak-proof containers and labeled appropriately. The operator shall notify the local health department and the [Executive Secretary]Director if the operator believes that the regulated asbestos-containing material is in a condition that may cause fiber release during disposal. If the wastes are not properly containerized, and the landfill operator accepts the load, the operator shall thoroughly soak the regulated asbestos-containing material with a water spray prior to unloading, rinse out the truck, and immediately cover the regulated asbestos-containing material with material which prevents fiber release prior to compacting the regulated asbestos-containing material in the landfill.

    (c) During deposition and covering of the regulated asbestos-containing material, the operator:

    (i) may prepare a separate trench or separate area of the landfill to receive only regulated asbestos-containing material, or may dispose of the regulated asbestos-containing material at the working face of the landfill;

    (ii) shall place the regulated asbestos-containing material containers into the trench, separate area, or at the bottom of the landfill working face with sufficient care to avoid breaking the containers;

    (iii) within 18 hours or at the end of the operating day, shall completely cover the containerized regulated asbestos-containing material with sufficient care to avoid breaking the containers with a minimum of six inches of material containing no regulated asbestos-containing material. If the regulated asbestos-containing material is improperly containerized, it must be completely covered immediately with six inches of material containing no regulated asbestos-containing material; and

    (iv) shall not compact regulated asbestos-containing material until completely covered with a minimum of six inches of material containing no regulated asbestos-containing material.

    (d) The operator shall provide barriers adequate to control public access. At a minimum, the operator shall:

    (i) limit access to the regulated asbestos-containing material management site to no more than two entrances by gates that can be locked when left unattended and by fencing adequate to restrict access by the general public; and

    (ii) place warning signs at the entrances and at intervals no greater than 330 feet along the perimeter of the sections where regulated asbestos-containing material is deposited that comply with the requirements of 40 CFR 61.154(b); and

    (e) close the separate trenches, if constructed, according to the requirements of Subsection R315-303-3(4) with the required signs in place.

     

    R315-315-7. PCB Containing Waste.

    (1) Any facility that disposes of nonhazardous waste, hazardous waste, or radioactive waste containing PCBs is regulated by Rules R315-301 through 320.

    (2) The following wastes containing PCBs may be disposed in a permitted Class I, II, III, IV, V, or VI Landfill; permitted incinerator; permitted energy recovery facility; or a facility permitted by rule under Rule R315-318:

    (a) waste, as specified by 40 CFR 761.61, containing PCBs at concentrations less than 50 ppm;

    (b) PCB household waste as defined by 40 CFR 761.3 ; and

    (c) small quantities, 10 or fewer, of intact, non-leaking, small PCB capacitors, including capacitors from fluorescent lights x-ray machines, and other machines and test equipment.

    (3) Waste containing PCBs at concentrations of 50 ppm or higher are prohibited from disposal in a landfill, incinerator, or energy recovery facility that is regulated by Rules R315-301 through 320, except:

    (a) the following facilities may receive waste containing PCBs at concentrations of 50 ppm or higher for treatment or disposal:

    (i) a facility permitted prior to July 15, 1993 under 40 CFR 761.70, .75 or .77; or

    (ii) a facility permitted after July 15, 1993 under 40 CFR 761.70, .71, .72, .75, or .77 and approved by the [Executive Secretary]Director under Rules R315-301 through 320; or

    (b) a Class I or V landfill that has a liner and ground water monitoring or an incinerator that meets the requirements of Subsection R315-315-7(a)(i) or (ii) and when approved by the [Executive Secretary]Director, may dispose of the following PCB wastes:

    (i) PCB bulk products regulated by 40 CFR 761.62(b);

    (ii) drained PCB contaminated equipment as defined by 40 CFR 761.3;

    (iii) drained PCB articles, including drained PCB transformers, as defined by 40 CFR 761.3;

    (iv) non-liquid cleaning materials remediation wastes containing PCB's regulated by 40 CFR 761.61(a)(5)(v)(A);

    (v) PCB containing manufactured products regulated by 40 CFR 761.62(b)(1)(i) and (ii); or

    (vi) non-liquid PCB containing waste, initially generated as a non-liquid waste, generated as a result of research and development regulated by 40 CFR 761.64(b)(2).

    (c) If a unit of a permitted landfill is approved to receive PCB containing wastes under Subsection R315-315-7(3)(b), the owner or operator of the landfill:

    (i) shall modify the approved Ground Water Monitoring Plan to include the testing of the ground water samples for PCB containing constituents at appropriate detection levels; and

    (ii) shall test the leachate generated at the unit of the landfill for PCB's.

     

    KEY: solid waste management, waste disposal

    Date of Enactment or Last Substantive Amendment: [January 13, 2012]2013

    Notice of Continuation: February 14, 2008

    Authorizing, and Implemented or Interpreted Law: 19-6-105

     


Document Information

Effective Date:
4/15/2013
Publication Date:
03/01/2013
Filed Date:
02/15/2013
Agencies:
Environmental Quality,Solid and Hazardous Waste
Rulemaking Authority:

Section 19-6-108

Section 19-6-105

Section 19-6-107

Authorized By:
Scott Anderson, Director
DAR File No.:
37336
Related Chapter/Rule NO.: (1)
R315-315. Special Waste Requirements.