No. 31909 (New Rule): R392-303. Public Geothermal Pools and Bathing Places

DAR File No.: 31909
Filed: 08/28/2008, 05:10
Received by: NL

RULE ANALYSIS

Purpose of the rule or reason for the change:

This rule makes allowances for the special circumstances inherent with the design, construction, and operation of geothermal pools and natural bathing places that are not covered in Rule R392-302 (Public Pool rule). This rule is in response to a legislative request.

Summary of the rule or change:

The rule makes special allowances for geothermal pools that are not provided for in Rule R392-302 (Swimming Pool rule) but contains many provisions that require compliance with Rule R392-302 under circumstances where geothermal pools and natural bathing places do not need special provisions. The rule does not require a construction change to existing pools and does not require the upgrade of an entire pool if one aspect of the pool is upgraded. The rule allows public geothermal pools to use natural geothermal water source rather than water from a public drinking water supply. The rule, however, requires testing of the water and determining the possible health effects of bathing in it. The rule allows flow-through and bather load to be used as the only methods of pool water contamination control (allows pools to operate without filtration or disinfection) but requires notification to bathers of that fact and the potential risk. Higher turnover rates are required in geothermal pools than other public pools but the requirement can be decreased, or increased, by the local health department based on bacterial tests. The rule allows natural walls, floors, water depth, and floor slopes of natural bathing places that would not be allowed under the public pool rule but the rule provides for the safety of bathers by other means such as notifications, roping off areas, and barriers. The rule requires bacteriological monitoring but makes an allowance for higher levels of bacterial contamination than other public pools. Bather notification is required when the bacterial level exceeds that allowed in other public pools. The rule allows local health departments to require operators to admit fewer bathers in a pool if bacterial levels are consistently high and requires the closing of a pool if maximum levels are exceeded.

State statutory or constitutional authorization for this rule:

Section 26-15-2

Anticipated cost or savings to:

the state budget:

There will be no impact on the state budget as the local health departments are charged with the responsibility of inspecting public pools.

local governments:

Many of the existing geothermal pools and natural bathing places in the state are already permitted and inspected by local health departments. The new rule should not affect the costs to inspect these existing facilities. It is estimated that there are approximately three geothermal facilities in the state that local health departments have chosen not to permit because the pool rule did not provide for their unique circumstances. When this new rule is effective, these three facilities will need to be permitted. Any increase in costs for the new regulation of those facilities should be mostly offset by permit fees.

small businesses and persons other than businesses:

There are approximately eight geothermal facilities with an average of three pools per facility in the state that will be affected by this rule. These facilities will have to pay for sampling fees, source analysis, flow meters, permits, and new signs. The initial total aggregate annual cost to these facilities to be compliant with the requirements of the new rule is estimated to be $2,460 per facility, or (8 x $2,460) a total $19,680 aggregate cost. (Sampling fee: $300, Source analysis: $300; Flow meter: 3 x $400 = $1,200; Signs: 12 x $30 = $360; Permit: $100 per pool, 3 x 100 = $300). The estimated ongoing costs would amount to $660 per year ($300 sampling + $300 permit + 1/5 x $300 source analysis = $660), or (8 x 660 = $5,280) a total $5,280 per year aggregate costs.

Compliance costs for affected persons:

All geothermal pools will be required to have a flow meter to measure flow through of water. The minimum cost of a low end flow meter is approximately $400, plus installation. High end flow meters can cost up to $2,000, plus installation. All geothermal pools would have initial (and every five year) costs for water analysis of their source water. This cost should be less than $300 per water source. There may also be ongoing water quality analysis costs associated with the permit. It is estimated that these would not be more than $300 per year. Pools will have to acquire notification signs with an estimated number of 12 signs per facility. The cost of a sign is approximately $30 - $40 per sign. This would result in a cost of $360 - $480 per facility. Pools not regulated at the present time that will be required to be permitted would have to pay permit fees of approximately $100 per pool.

Comments by the department head on the fiscal impact the rule may have on businesses:

In response to requests from facilities that operate geothermal pools, this rule proposes special standards for this type of pool. Public input during the development rule is reflected in the rule and additional comments will be considered. David N. Sundwall, MD, Executive Director

The full text of this rule may be inspected, during regular business hours, at the Division of Administrative Rules, or at:

Health
Epidemiology and Laboratory Services, Environmental Services
CANNON HEALTH BLDG
288 N 1460 W
SALT LAKE CITY UT 84116-3231

Direct questions regarding this rule to:

Ronald Marsden at the above address, by phone at 801-538-6191, by FAX at 801-538-6564, or by Internet E-mail at [e-mail]

Interested persons may present their views on this rule by submitting written comments to the address above no later than 5:00 p.m. on:

10/15/2008

This rule may become effective on:

10/22/2008

Authorized by:

David N. Sundwall, Executive Director

RULE TEXT

R392. Health, Epidemiology and Laboratory Services, Environmental Services.

R392-303. Public Geothermal Pools and Bathing Places.

R392-303-1. Authority and Purpose.

This rule is authorized under Section 26-15-2. It establishes minimum standards for the design, construction, operation and maintenance of public geothermal pools and public geothermal bathing places.

 

R392-303-2. Definitions.

The following definitions apply in this rule.

(1) "Bather load" means the number of persons allowed by the operator to use a geothermal pool or geothermal bathing place at any one time or specified period of time.

(2) "Department" means the Utah Department of Health.

(3) "Executive Director" means the Executive Director of the Utah Department of Health, or his designated representative.

(4) "Flow-through" means water that is fed by a continuous supply into a pool or bathing place that causes an equal rate of flow to discharge from the pool or bathing place to waste.

(5) "Geothermal bathing place" means a natural bathing place or semi-artificial bathing place with an impoundment of geothermal water.

(6) "Geothermal pool" means a man-made basin, chamber, receptacle, tank, or tub which is filled with geothermal water or a mixture of geothermal and non-geothermal water that creates an artificial body of water.

(7) "Geothermal water" means ground water that is heated in the earth by the earth's interior.

(8) "Living unit" means one or more rooms or spaces that are, or can be, occupied by an individual, group of individuals, or a family, temporarily or permanently for residential or overnight lodging purposes. Living units include motel and hotel rooms, condominium units, travel trailers, recreational vehicles, mobile homes, single family homes, and individual units in a multiple unit housing complex.

(9) "Local Health Officer" means the health officer of the local health department having jurisdiction, or his designated representative.

(10) "Natural bathing place" means a lake, pond, river, stream, swimming hole, or hot springs which has not been modified by man.

(11) "Semi-artificial bathing place" means a natural bathing place that has been modified by man.

 

R392-303-3. General Requirements.

(1) This rule applies to geothermal pools and geothermal bathing places that:

(a) are partially or completely filled with geothermal water that has a source temperature of at least 70 degrees Fahrenheit, 21.1 degrees Celsius; and

(b) are offered to the public for bathing or recreation.

(2) This rule does not apply to an unsupervised geothermal bathing place that the owner explicitly or tacitly allows anyone at any time to use without a fee.

(3) This rule does not apply to a geothermal pool or geothermal bathing place that is used only by a single household or only by a single group of multiple living units of four or fewer households.

(4) Except as otherwise stated in this rule, geothermal pools and geothermal bathing places , are exempt from the requirements of R392-302.

(5) This rule does not require an owner or operator to modify any portion of an existing geothermal pool facility or existing geothermal bathing place. If an owner or operator modifies any system or part of a geothermal pool or geothermal bathing place, the modified system or part must meet the requirements of this rule. However, if the Executive Director or the Local Health Officer determines that any facility is dangerous, unsafe, unsanitary, or a nuisance or menace to life, health or property, the Executive Director or the Local Health Officer may order modification consistent with the requirements of this rule.

 

R392-303-4. Drinking Water Supply.

(1) The owner of a geothermal pool or geothermal bathing place shall assure that all plumbing fixtures including drinking fountains, lavatories and showers at the public geothermal pool or geothermal bathing place facility are connected to a drinking water system that meets the requirements for drinking water established by the Utah Department of Environmental Quality.

(2) The owner of a geothermal pool or geothermal bathing place shall protect the connected drinking water system against back flow of contamination or back flow of water from the geothermal water source.

 

R392-303-5. Geothermal Water Quality.

(1)(a) The owner of a geothermal pool or geothermal bathing place shall install a tap or sampling point that provides the operator with the ability to sample the geothermal source water before it enters the geothermal pool or geothermal bathing place impoundment.

(b) If it is impractical to directly sample the geothermal water, the operator may sample water directly from the pool or impoundment. However, at least sixteen hours must have passed since any person has been in the pool and the sample shall be taken as close to the geothermal source water inlet as practical.

(2) The owner of a geothermal pool or bathing place shall protect source water from contamination in transit between the source spring or well and the pool or bathing place.

(3) The operator of a geothermal pool or geothermal bathing place shall submit samples of the geothermal source water for analysis to a laboratory certified under R444-14. The operator shall have the analysis performed initially and every five years thereafter to determine the levels of constituents listed in Table 1. If a geothermal pool or geothermal bathing place is in existence prior to the adoption of this rule, the owner of the facility shall submit to the local health department the results of initial source water tests within six months after the adoption of the rule. The permit applicant of a newly permitted public geothermal pool or geothermal bathing place shall submit the results of the initial source water analyses to the local health department with his application for a permit. The operator shall submit five-year samples to the local health department within six months prior to the end of the five year period.

(4) If the geothermal source water analysis required in R392-303-5(3) reports that any constituents exceed the limits in Table 1, the owner shall do one of the following:

(a) not use the source water;

(b) implement an ongoing treatment process approved by the Local Health Officer to provide source water that meets the requirements in Table 1; or

(c) submit results of the source water analysis to a toxicologist certified as a Diplomat of the American Board of Toxicology and implement, after approval by the Local Health Officer, a plan that includes the recommendations of the toxicologist to protect the health of bathers that use the geothermal pool or geothermal bathing place.

 

TABLE 1

Geothermal Source Water Constituents



Constituent                    Maximum                  Minimum



pH                          8.0                            7.0

Fluoride                    4.0 milligrams per liter      None

Nitrate                     10 milligrams per liter       None

Nitrite                     1 milligrams per liter        None

Antimony                    0.006 milligrams per liter    None

Arsenic                     0.010 milligrams per liter    None

Barium                      2 milligrams per liter        None

Beryllium                   0.004 milligrams per liter    None

Cadmium                     0.005 milligrams per liter    None

Chromium                    0.1 milligrams per liter      None

Copper                      1.3 milligrams per liter      None

Cyanide (as free cyanide)   0.2 milligrams per liter      None

Lead                        0.015 milligrams per liter    None

Mercury                     0.002 milligrams per liter    None

Selenium                    0.05 milligrams per liter     None

Thallium                    0.002 milligrams per liter    None

 

R392-303-6. General Safety Requirements.

(1) Geothermal pools shall meet the requirements of R392-302-11.

(2) Head-first entry is not permitted at a geothermal bathing place except where the operator has demonstrated to the local health officer that the water depth and underwater obstructions at the entire geothermal bathing place pose no greater risk than at a diving-permitted section of a swimming pool as allowed in R392-302-11. Diving with a self-contained underwater breathing apparatus (SCUBA) is allowed at geothermal bathing places. Where head-first entry is not permitted, the operator shall place a sign that states "NO HEAD-FIRST ENTRY" in accordance with R392-303-22, 23 and 24.

(3) Geothermal pools and geothermal bathing places shall meet the following sections of R392-302:

(a) R392-302-14 Fencing;

(b) R392-302-22 Safety Requirements and Lifesaving Equipment;

(c) R392-302-23 Lighting, Ventilation and Electrical Requirements; and

(d) R392-302-30 Supervision of Bathers subsections 1 through 7.

 

R392-303-7. Bather Facilities.

Geothermal pools and geothermal bathing places shall meet the following sections of R392-302:

(1) R392-302-24 Dressing Rooms

(2) R392-302-25 Toilets and Showers

(3) R392-302-26 Visitors and Spectator Areas

 

R392-303-8. Construction Materials.

(1) Geothermal pools shall meet the requirements of R392-302-6.

(2) The owner or operator of a geothermal bathing place shall notify bathers of and protect them from safety hazards by methods such as altering surfaces or structures, barricading or roping off problem areas, and posting warning signs.

 

R392-303-9. Bather Load.

(1) Geothermal pools and geothermal bathing places shall meet the bather load requirements in R392-302-7.

(2) If a geothermal pool or geothermal bathing place is unable to meet bacteriological water quality by other means, the Local Health Officer may require the owner or operator to reduce the allowed bather load in order to meet the requirements R392-303-19.

 

R392-303-10. Design Detail and Structural Stability.

(1) With the exception of the provisions listed in R392-302-8(3) and R392-302-8(5), geothermal pools shall meet the provisions of R392-302-8.

(2) The owner shall submit plans for a new geothermal pool or a geothermal bathing place or the renovation or the remodeling of a geothermal pool or a geothermal bathing place to the local health department for approval based upon compliance to this rule. Renovation or remodeling includes the replacement or modification of equipment that may affect the ability of a geothermal pool or a geothermal bathing place to meet the safety and water quality standards of this rule.

 

R392-303-11. Depths and Floor Slopes.

(1) Geothermal pools shall meet the requirements of R392-302-9.

(2) The owner of a geothermal bathing place shall protect bathers from uneven bottoms, sudden changes in depth, and other bottom anomalies by altering the pool bottom, posting signs about the dangers, providing barriers around hazards, or roping off areas.

 

R392-303-12. Walls.

(1) Geothermal pools shall meet the requirements of R392-302-10.

(2) The owner of a geothermal bathing place shall protect bathers from uneven walls, submerged projections, or submerged ledges by methods such as posting signs notifying patrons of the dangers, providing barriers around hazards, or roping off areas,

 

R392-303-13. Ladders, Recessed Steps, and Stairs.

(1) Geothermal pools shall meet the requirements of R392-302-12.

(2) The owner of a geothermal bathing place shall provide a means of entrance into and exit from the water that include handholds and steps where needed to provide for bather safety.

 

R392-303-14. Decks and Walkways.

(1) Geothermal pools shall meet the requirements of R392-302-13.

(2) The owner of a geothermal bathing place shall provide safe walkways leading to the bathing place that are free of trip hazards and provide handholds where there are ramps or steps.

 

R392-303-15. Depth Markings and Safety Ropes.

(1) Geothermal pools shall meet the requirements of R392-302-15.

(2) The owner of a geothermal bathing place shall protect bathers from unexpected deep water by means such as posting pool depth signs, providing barriers around deep areas, or roping off areas.

 

R392-303-16. Circulation Systems.

(1) Geothermal pools shall meet the requirements of R392-302-16 for normal water line, piping, pipe labeling, velocity in pipes, vacuum cleaning systems, adequate space in equipment areas, valves, and air induction systems.

(2) The owner or operator of a geothermal pool or geothermal bathing place shall maintain flow-through 24 hours a day during the operating season, except for periods of maintenance. If the pool is drained and cleaned each day prior to use, flow-through is only required during the period that the geothermal pool is in use.

(3) A geothermal pool or geothermal bathing place with a volume greater than 3,000 gallons, 11,355 liters, shall have a flow-through rate greater than or equal to one-fourth the pool volume every hour. A geothermal pool or geothermal bathing place with a volume less than or equal to 3,000 gallons, 11,355 liters, shall have a flow-through rate greater than or equal to the pool volume every 30 minutes.

(a) If the results of any three of the last five E. Coli or fecal coliform samples taken from the pool exceed 63 per 50 milliliters, the Local Health Officer may require an increased rate of flow-through independent of or in addition to a bather load reduction as provided in R392-303-9(2).

(b) The Local Health Officer may approve a reduced flow rate if the owner or operator of the geothermal pool or geothermal bathing place can demonstrate that the required bacteriological level can be maintained at the reduced flow rate.

(4) A geothermal pool that has pumped flow shall meet the inlet requirements of R392-302-17. Geothermal bathing places and geothermal pools that have gravity flow inlets, shall either meet the requirements of R392-302-17 or the owner or operator of the pool shall demonstrate to the local health department that the inlet system provides uniform distribution of fresh water throughout the pool. A demonstration of uniform distribution includes computer simulation or a dye test witnessed by a representative of the local health department.

(5) A geothermal pool shall have a drain that allows complete emptying of the pool. Geothermal pool and geothermal bathing place submerged drain grates and covers shall meet the requirements of R392-302-18. Geothermal pool and geothermal bathing place submerged drains shall meet the anti-entrapment requirements of R392-302-18.

(6) A geothermal pool shall have overflow gutters or skimming devices that meet the applicable requirements of R392-302-19.

(7) Geothermal pools and geothermal bathing places shall have an accurate rate-of-flow indicator, reading in gallons per minute. If the rate-of-flow indicator is manufactured by a third party, it shall be properly installed and located according to the manufacturer's recommendations. If a field-fabricated rate-of-flow indicator such as a calibrated weir or flume is used, it shall be designed and calibrated under the direction of a licensed professional engineer. The rate-of-flow indicator must be located in a place and positioned where it can be easily read by the operator as required in R392-303-21(2). The Local Health Officer may exempt a geothermal pool or geothermal bathing place from the requirement for a rate-of-flow indicator if the rate of flow is not adjustable or if there is no practical way to measure flow.

(8) Each geothermal pool and geothermal bathing place shall have a temperature measuring device that continuously measures the temperature of the pool at the warmest point. The device shall be accurate to within one degree Fahrenheit (0.6 degrees Celsius). The operator shall calibrate the thermometer in accordance with the manufacturer's specifications as necessary to ensure its accuracy.

 

R392-303-17. Filtration.

The owner of a flow-through geothermal pool or geothermal bathing place is not required to filter the water in the pool or bathing place, except as may be necessary to meet safety and water quality requirements. Filters shall meet the requirements of R392-302-20.

 

R392-303-18. Disinfectant and Chemical Feeders.

Chemical feeders or disinfectant residuals are not required in geothermal pools or geothermal bathing places, except as may be necessary to meet water quality requirements. If the operator uses any chemical, the operator shall meet the requirements of R392-302-21 for that particular chemical.

 

R392-303-19. Quality of Water.

(1) The water in a geothermal pool or geothermal bathing place must have sufficient clarity at all times so that a black disc 6 inches, 15.24 centimeters, in diameter, is readily visible if placed on a white field at the deepest point of the pool (or at 12 feet, 3.66 meters, deep for pools over 12 feet, 3.66 meters, deep). The owner or operator shall close the pool or bathing place immediately if this requirement is not met.

(2) The local health department or, if the Local Health Officer chooses, the owner or operator of a geothermal pool or geothermal bathing place shall collect bacteriological samples of the pool water at least twice per month at lease one week apart or as otherwise directed by the Local Health Officer. The Local Health Officer shall choose or approve the dates and times that the samples are collected, The Local Health Officer shall choose dates and times when a representative level of bacteria would likely be found. The local health department or the operator, as required by local health department, shall submit the bacteriological samples to a laboratory approved by under R444-14 to perform E. coli or fecal coliform testing.

(a) The local health department or operator, as required by local health department, shall have the laboratory analyze the sample for either E. coli or fecal coliform.

(b) If the operator submits the sample as required by local health department, the operator shall require the laboratory to report sample results within five working days to the local health department and operator.

(3) If the E. coli or fecal coliform levels are found to be greater than the maximum level of 63 per 50 milliliters, the owner or operator shall close the pool until sample results show the level is below 63.

(4) If E. coli or fecal coliform levels are greater than one per 50 milliliters, the pool operator shall post the level found as required in R392-303-22.

(5) The owner or operator of a geothermal pool or geothermal bathing place should maintain the pool water temperature at a maximum of 104 degrees Fahrenheit, 40 degrees Celsius. A geothermal pool or geothermal bathing place that exceeds 104 degrees Fahrenheit, 40 degrees Celsius, at the minimum required turnover rate shall have, and employ when necessary, a method of temperature reduction in the pool or bathing place that maintains the minimum flow-through rate required under R392-303-16(3). An approved method of temperature reduction may include methods such as the introduction of cool water from a source approved by the Local Health Officer, the direct cooling of the geothermal source water, and diversion of the geothermal source water to allow it to cool prior to entering the pool or impountment. The temperature reduction method shall be capable of reducing the temperature of the pool within 2 hours of activation from the maximum anticipated temperature to below 104 degrees Fahrenheit, 40 degrees Celsius. If the temperature of the source water or cooling rate of the pool is difficult to control, a temperature drift of up to four degrees Fahrenheit, 2.2 degrees Celsius, may be allowed by the Local Health Officer if the owner or operator has activated the temperature reduction measure. The owner or operator of a geothermal pool or geothermal bathing place shall not permit bathers to use the pool if the temperature is above 108 degrees Fahrenheit, 42.2 degrees Celsius.

 

R392-303-20. Cleaning Pools.

(1) The owner or operator of a geothermal pool shall remove any visible dirt on the bottom of the pool at least once every 24 hours or more frequently as needed to keep the pool free of dirt and debris.

(2) The owner or operator of a geothermal pool or geothermal bathing place shall clean the water surface of the pool as often as needed to keep the pool free of scum or floating matter.

(3) The owner or operator of a geothermal pool shall keep pool surfaces, decks, handrails, floors, walls, and ceilings of rooms enclosing pools, dressing rooms and equipment rooms clean, sanitary, and in good repair. The owner or operator of a geothermal bathing place shall keep handholds, handrails, entrance points, walkways, dressing rooms, and equipment rooms clean and in good repair.

 

R392-303-21. Supervision of Pools.

(1) Geothermal pools and geothermal bathing places shall meet the requirements of R392-302-29(1).

(2) The operator of a geothermal pool or geothermal bathing place shall record the flow-through rate and pool temperature prior to opening the pool or bathing place each day and every four hours that the pool is open. The operator shall record the number of pool users every four hours that the pool is open for use. If a pool uses disinfection or filtration, the operator shall keep the disinfection and filtration records required in R392-302-29. The Local Health Officer may alter the requirement for the frequency of record keeping if an increased or decreased frequency is more reasonable considering the likelihood of a change in the values recorded. The owner or operator shall make the records required by this section available for inspection by representatives of the local health department and shall retain the records for at least three years.

 

R392-303-22. Caution Sign Content.

(1)(a) The operator of a geothermal pool or a geothermal bathing place in which the requirements of Table 6 in R392-302-27 are not met for disinfectant residual shall post a caution sign with the following bulleted points:

-WATER IN THIS POOL CONTAINS NO DISINFECTANT

-BATHING IN THIS POOL MAY INCREASE YOUR RISK OF INFECTIOUS DISEASE

-PERSONS SUFFERING FROM A COMMUNICABLE DISEASE TRANSMISSIBLE BY WATER SHALL NOT ENTER THE WATER

-KEEP POOL WATER OUT OF YOUR MOUTH AND NOSE.

(b) The operator shall post an additional sign or an addition to the sign required by this section that describes the results of the sample using a changeable element such as a "white board" or attachable digits. The sign shall state:

-THE MOST RECENT BACTERIAL RESULT OF WATER FROM THIS POOL WAS (the changeable element shall be placed at this point with the most recent fecal coliform or E. coli count per 50 milliliters posted). FOR COMPARISON, A NON-GEOTHERMAL POOL CANNOT EXCEED 1

(c) If ozone or ultraviolet light is used to treat the water, the following statement may be added to the sign; the statement shall be verbatim and state the method of treatment:

-TREATED WITH (UV LIGHT or OZONE or UV LIGHT AND OZONE if both are used)-PROVIDES SHORT-TERM DISINFECTION ONLY.

(2) If a geothermal pool or geothermal bathing place is operated at a temperature greater than or equal to 100 degrees Fahrenheit, 37.8 degrees Celsius, the operator shall post a separate caution sign that includes the following bulleted points:

-POOL WATER MAY EXCEED 100 DEGREES F. (37.8 DEGREES C.)

-CONSULT A PHYSICIAN IF YOU: ARE ELDERLY OR PREGNANT; HAVE HEART DISEASE, DIABETES, OR HIGH BLOOD PRESSURE; OR USE PRESCRIPTION MEDICATION

-DO NOT USE POOL IF ALONE OR UNDER THE INFLUENCE OF ANY IMPAIRING SUBSTANCE

-DO NOT USE POOL FOR MORE THAN 15 MINUTES AT A TIME

-CHILDREN UNDER 5 ARE PROHIBITED; CHILDREN UNDER 14 MUST BE WITH A PERSON OVER 18 YEARS

(3) Except at a geothermal pool or a geothermal bathing place where head-first entry is permitted, the operator shall post a warning sign that states, "NO HEAD-FIRST ENTRY" in accordance with R392-303-23 and 24.

 

R392-303-23. Caution Sign Placement.

The operator of a geothermal pool or geothermal bathing place shall post caution and warning signs that meet the requirements of this rule in conspicuous locations that are in the line of sight of a persons using the premises and readily visible so that all persons are alerted to potential hazards and informed before using the geothermal pool or geothermal bathing place.

(1) The operator shall place the caution sign required in subsection R392-303-22(1) at the reception or sales counter and no more than 10 feet from where a person checks in or pays for the use of the pool. The sign shall be visible to potential customers before they pay for entry or pass the reception or sales counter. If there are multiple geothermal pools or geothermal bathing places at the facility, the operator shall display on the caution sign at the reception or sales counter the bacterial count of the geothermal pool or geothermal bathing place in the facility that had the highest level of E. coli or fecal coliform found in the most recent sampling event. The operator shall post an additional sign required in R392-303-22(1) at each pool or bathing place. The operator shall post the sign in a location and position readily visible and within ten feet, 3 meters, of at least one point at the water's edge. The operator shall display on the additional sign the most recent E. coli or fecal coliform count of the particular geothermal pool or geothermal bathing place.

(2) The operator shall place any caution sign required in subsection R392-303-22(2) either:

(a) next to the sign required in subsection R392-303-22(1) if the pool or all pools may exceed 100 degrees Fahrenheit, 37.8 degrees Celsius; or

(b) within 10 feet of the entrance or entrances to each pool that is operated at a temperature greater than or equal to 100 degrees Fahrenheit, 37.8 degrees Celsius.

(3) The operator shall place any warning sign required in subsection R392-303-22(3) either:

(a) next to the sign(s) required in subsection R392-303-22(1) if the pool or all pools do not permit head-first entry; or

(b) within 10 feet of the entrance or entrances to each pool that does not permit head-first entry.

 

R392-303-24. Caution Sign Format Requirements.

(1) The caution sign required by R392-303-22(1) and R392-303-22(2) shall meet the following requirements:

(a) The signs shall be at least 24 inches, 61 centimeters, by 18 inches, 46 centimeters, on a white background. If the sign is larger than 24 inches, 61 centimeters, by 18 inches, 46 centimeters, the sizes of the other elements of the sign shall be proportionally larger.

(b) All lettering shall be in a sans serif font proportional thickness to height so as to be easily readable. Acceptable fonts are arial bold, folio medium, franklin gothic, helvetica, helvetica bold, meta bold, news gothic bold, poster gothic, and universe. In addition, the letters shall be:

(i) black in color;

(ii) capital letters; and

(iii) adequately spaced and not crowded.

(c) There must be a panel at the top of the sign. The background of the panel shall be safety yellow in color and shall:

(i) be at least 3.3 centimeters, high and 44 centimeters wide, including a black line border that is 0.16 centimeters wide surrounding the safety yellow background;

(ii) have the word "CAUTION" in capital letters that are two centimeters high; and

(iii) have an internationally recognized safety alert symbol that is two centimeters high and placed immediately to the left of the word "CAUTION".

(d) The safety alert symbol shall be black with a yellow field.

(e) The word "CAUTION" and the symbol shall be vertically and horizontally centered within the yellow panel.

(f) The letters in the body of the sign shall be legible, at least one centimeter high, and clearly visible.

(g) The body of the sign required in subsection R392-303-22(1) shall list the bulleted statements required in that section.

(h) The body of the sign required in subsection R392-303-22(2) shall list the bulleted statements required in that section.

(2) The warning sign required by R392-303-22(3) shall meet the following requirements:

(a) The signs shall be at least 17 inches, 43 centimeters, by 11 inches, 28 centimeters, on a white background. If the sign is larger than 17 inches, 43 centimeters, by 11 inches, 28 centimeters, the sizes of the other elements of the sign shall be proportionally larger.

(b) All lettering shall be in a sans serif font proportional thickness to height so as to be easily readable. Acceptable fonts are arial, arial bold, folio medium, franklin gothic, helvetica, helvetica bold, meta bold, news gothic bold, poster gothic, and universe. In addition, the letters shall be:

(i) black in color;

(ii) capital letters; and

(iii) adequately spaced and not crowded.

(c) There must be a panel at the top of the sign. The background of the panel shall be safety orange in color and shall:

(i) be at least 3.3 centimeters, high and 41 centimeters wide, including a black line border that is 0.16 centimeters wide surrounding the safety orange background;

(ii) have the word "WARNING" in capital letters that are two centimeters high; and

(iii) have an internationally recognized safety alert symbol that is two centimeters high and placed immediately to the left of the word "WARNING".

(d) The safety alert symbol shall be black with a safety orange field.

(e) The word "WARNING" and the symbol shall be vertically and horizontally centered within the orange panel.

(f) The letters in the body of the sign shall be legible, at least one inch (2.54 centimeters) high, and clearly visible

(g) The body of the sign required in subsection R392-303-22(3) shall display the text "NO HEAD-FIRST ENTRY". The text on the body shall be centered vertically and horizontally in the space below the orange panel with "NO HEAD-FIRST" on one line and "ENTRY" on the line below.

 

R392-303-25. Enforcement and Penalties.

A person who violates a provision of this rule is subject to a Class B misdemeanor on the first offense or a Class A misdemeanor on the second offense within one year or a civil penalty of up to $5,000 for each offense as provided in Section 26-23-6.

 

KEY: geothermal pools, geothermal natural bathing places, hot springs, geothermal spas

Date of Enactment or Last Substantive Amendment: 2008

Authorizing, Implemented, or Interpreted Law: 26-15-2