No. 41348 (Amendment): Rule R156-55a. Utah Construction Trades Licensing Act Rule  

  • (Amendment)

    DAR File No.: 41348
    Filed: 03/07/2017 08:58:23 AM

    RULE ANALYSIS

    Purpose of the rule or reason for the change:

    The purpose of this rule filing is to make technical name changes and to modify continuing education requirements as approved by the Construction Services Commission and the Division.

    Summary of the rule or change:

    In Subsections R156-55a-301(2) and R156-55a-302b(5), the proposed amendment is a technical change of name for the National Radon Proficiency Program from NEHA-NRPP to AARST-NRPP. The entity has changed the name of the certificate it issues. In Subsection R156-55a-303b(1)(a), the proposed amendment adds construction business practices to the list of courses that qualify as core continuing education. New Section R156-55a-303b(2)(i) allows live continuing education courses to be taught by live broadcast so long as the instructor and student can see and hear each other.

    Statutory or constitutional authorization for this rule:

    Anticipated cost or savings to:

    the state budget:

    The Division will incur minimal costs of approximately $75 to print and distribute the rule once the proposed amendments are made effective. Any costs incurred will be absorbed in the Division's current budget.

    local governments:

    The proposed amendments apply only to licensed contractors. None of these amendments will affect local government; therefore, there is no cost or savings impact to local government.

    small businesses:

    Subsections R156-55a-301(2) and R156-55a-302b(5) include a technical change of name, which will not impact small business. Changes to Subsection R156-55a-303b(1) add construction business practices to the list of courses that qualify as core continuing education which is not anticipated to impact small business, except for indirect savings that may be experienced by some small business licensees who improve their business practices. The amount of savings cannot be estimated by the Division as it will vary depending on circumstances. The new Subsection R156-55a-303b(2)(i) allows live broadcast to count as live in-class attendance for continuing education credit, which will save some small business licensees the cost of traveling to a central location to obtain their required continuing education hours. This will be especially beneficial to small business licensees in remote, rural locations. The amount of savings cannot be estimated by the Division as it will vary depending on circumstances.

    persons other than small businesses, businesses, or local governmental entities:

    Subsections R156-55a-301(2) and R156-55a-302b(5) include a technical change of name, which will not impact other persons. Changes to Subsection R156-55a-303b(1) add construction business practices to the list of courses that qualify as core continuing education which is not anticipated to impact other persons, except for indirect savings that may be experienced by some licensees who improve their business practices. The amount of savings cannot be estimated by the Division as it will vary depending on circumstances. New Subsection 303b(2)(i) allows live broadcast to count as live in-class attendance for continuing education credit, which will save some licensees the cost of traveling to a central location to obtain their required continuing education hours. This will be especially beneficial to licensees in remote, rural locations. The amount of savings cannot be estimated by the Division as it will vary depending on circumstances.

    Compliance costs for affected persons:

    None of the proposed amendments are anticipated to have compliance costs for affected persons because the proposed amendments simply make technical changes and expand options for continuing education courses.

    Comments by the department head on the fiscal impact the rule may have on businesses:

    These rule amendments make technical name changes and modify continuing education requirements as approved by the Construction Services Commission. The amendments to Subsections R156-55a-301(2) and R156-55a-302b(5) change the designation of NEHA to AARST in seven separate locations in the rule. The amendment to Subsection R156-55a-303b(1)(a) adds "construction business practices" to the list of courses that qualify as core continuing education courses. The amendment to Subsection R156-55a-303b(2)(i) allows continuing education courses to be taught by live broadcast, so long as the instructor and student can see and hear each other. The change to the first subsections has no fiscal impact. The last two changes will result in cost savings to small business. However, the amount of savings cannot be estimated, as it will vary depending on circumstances.

    Francine A. Giani, Executive Director

    The full text of this rule may be inspected, during regular business hours, at the Office of Administrative Rules, or at:

    Commerce
    Occupational and Professional Licensing
    HEBER M WELLS BLDG
    160 E 300 S
    SALT LAKE CITY, UT 84111-2316

    Direct questions regarding this rule to:

    Interested persons may present their views on this rule by submitting written comments to the address above no later than 5:00 p.m. on:

    05/01/2017

    Interested persons may attend a public hearing regarding this rule:

    • 04/26/2017 09:15 AM, Heber Wells Bldg, 160 E 300 S, Conference Room 474, Salt Lake City, UT

    This rule may become effective on:

    05/08/2017

    Authorized by:

    Mark Steinagel, Director

    RULE TEXT

    R156. Commerce, Occupational and Professional Licensing.

    R156-55a. Utah Construction Trades Licensing Act Rule.

    R156-55a-301. License Classifications - Scope of Practice.

    (1) In accordance with Subsection 58-55-301(2), the classifications of licensure are listed and described in this section. The construction trades or specialty contractor classifications listed are those determined to significantly impact the public health, safety, and welfare. A person who is engaged in work which is included in the items listed in Subsections R156-55a-301(4) and (5) is exempt from licensure in accordance with Subsection 58-55-305(1)(i).

    (2) Licenses shall be issued in the following primary classifications and subclassifications:

    E100 - General Engineering Contractor. A General Engineering contractor is a contractor licensed to perform work as defined in Subsection 58-55-102(22).

    B100 - General Building Contractor. A General Building contractor is a contractor licensed to perform work as defined in Subsection 58-55-102(21) and pursuant to Subsection 58-55-102(21)(b) is clarified as follows:

    (a) The General Building Contractor scope of practice does not include activities described in this Subsection under specialty classification S202 - Solar Photovoltaic Contractor unless the work is performed under the immediate supervision of an employee who holds a current certificate issued by the North American Board of Certified Energy Practitioners.

    (b) The General Building Contractor scope of practice does not include activities described in this Subsection under specialty classification S354-Radon Mitigation Contractor unless

    (i) the work is performed under the immediate supervision of an employee who holds a current certificate issued by the National Radon Safety Board (NRSB) or the National Radon Proficiency Program ([NEHA]AARST-NRPP); or

    (ii) the work is limited to installation of passive radon gas controls on new construction in accordance with Appendix F of the International Residential Code.

    B200 - Modular Unit Installation Contractor. Set up or installation of modular units as defined in Subsection 15A-1-302(8) and constructed in accordance with Section 15A-1-304. The scope of the work permitted under this classification includes construction of the permanent or temporary foundations, placement of the modular unit on a permanent or temporary foundation, securing the units together if required and securing the modular units to the foundations. Work excluded from this classification includes installation of factory built housing and connection of required utilities.

    R100 - Residential and Small Commercial Contractor. A Residential and Small Commercial contractor is a contractor licensed to perform work as defined in Subsection 58-55-102(32) and pursuant to Subsection 58-55-102(32) is clarified as follows:

    (a) The Residential and Small Commercial Contractor scope of practice does not include activities described in this Subsection under specialty classification S202 - Solar Photovoltaic Contractor unless the work is performed under the immediate supervision of an employee who holds a current certificate issued by the North American Board of Certified Energy Practitioners.

    (b) The Residential and Small Commercial Contractor scope of practice does not include activities described in this Subsection under specialty classification S354-Radon Mitigation Contractor unless:

    (i) the work is performed under the immediate supervision of an employee who holds a current certificate issued by the National Radon Safety Board (NRSB) or the National Radon Proficiency Program ([NEHA]AARST-NRPP); or

    (ii) the work is limited to installation of passive radon gas controls on new construction in accordance with Appendix F of the International Residential Code.

    R101 - Residential and Small Commercial Non Structural Remodeling and Repair. Remodeling and repair to any existing structure built for support, shelter and enclosure of persons, animals, chattels or movable property of any kind with the restriction that no change is made to the bearing portions of the existing structure, including footings, foundation and weight bearing walls; and the entire project is less than $50,000 in total cost.

    R200 - Factory Built Housing Contractor. Disconnection, setup, installation or removal of manufactured housing on a temporary or permanent basis. The scope of the work permitted under this classification includes placement of the manufactured housing on a permanent or temporary foundation, securing the units together if required, securing the manufactured housing to the foundation, and connection of the utilities from the near proximity, such as a meter, to the manufactured housing unit and construction of foundations of less than four feet six inches in height. Work excluded from this classification includes site preparation or finishing, excavation of the ground in the area where a foundation is to be constructed, back filling and grading around the foundation, construction of foundations of more than four feet six inches in height and construction of utility services from the utility source to and including the meter or meters if required or if not required to the near proximity of the manufactured housing unit from which they are connected to the unit.

    I101 - General Engineering Trades Instruction Facility. A General Engineering Trades Instruction Facility is a construction trades instruction facility authorized to teach the construction trades and is subject to the scope of practice defined in Subsection 58-55-102(22).

    I102 - General Building Trades Instruction Facility. A General Building Trades Instruction Facility is a construction trades instruction facility authorized to teach the construction trades and is subject to the scope of practice defined in Subsections 58-55-102(21) or 58-55-102(32).

    I103 - Electrical Trades Instruction Facility. An Electrical Trades Instruction Facility is a construction trades instruction facility authorized to teach the electrical trades and subject to the scope of practice defined in Subsection R156-55a-301(S200).

    I104 - Plumbing Trades Instruction Facility. A Plumbing Trades Instruction Facility is a construction trades instruction facility authorized to teach the plumbing trades and subject to the scope of practice defined in Subsection R156-55a-301(S210).

    I105 - Mechanical Trades Instruction Facility. A Mechanical Trades Instruction Facility is a construction trades instruction facility authorized to teach the mechanical trades and subject to the scope of practice defined in Subsection R156-55a-301(S350).

    S200 - General Electrical Contractor. Fabrication, construction, and/or installation of generators, transformers, conduits, raceways, panels, switch gear, electrical wires, fixtures, appliances, or apparatus which utilizes electrical energy. The General Electrical Contractor scope of practice does not include activities described in this Subsection under specialty classification S354-Radon Mitigation Contractor unless the work is performed under the immediate supervision of an employee who holds a current certificate issued by the National Radon Safety Board (NRSB) or the National Radon Proficiency Program ([NEHA]AARST-NRPP).

    S201 - Residential Electrical Contractor. Fabrication, construction, and/or installation of services, disconnecting means, grounding devices, panels, conductors, load centers, lighting and plug circuits, appliances and fixtures in any residential unit, normally requiring non-metallic sheathed cable, including multiple units up to and including a four-plex, but excluding any work generally recognized in the industry as commercial or industrial.

    S202 - Solar Photovoltaic Contractor. Fabrication, construction, installation, and replacement of photovoltaic cell panels and related components. Wiring, connections and wire methods as governed in the National Electrical Code and Subsection R156-55b-102(1) shall only be performed by an S200 General Electrical Contractor or S201 Residential Electrical Contractor. This classification is not required to install stand alone solar systems that do not tie into premises wiring or into the electrical utility, such as signage or street or parking lighting.

    A contractor who obtained this classification of licensure between January 1, 2009 and April 25, 2011 and who holds an active license may, in addition to the above, perform the following activities as part of the scope of practice under this subsection: fabrication, construction, installation, and repair of photovoltaic cell panels and related components including battery storage systems, distribution panels, switch gear, electrical wires, inverters, and other electrical apparatus for solar photovoltaic systems. Work excluded from this classification includes work on any alternating current system or system component.

    S210 - General Plumbing Contractor. Fabrication and/or installation of material and fixtures to create and maintain sanitary conditions in buildings, by providing a permanent means for a supply of safe and pure water, a means for the timely and complete removal from the premises of all used or contaminated water, fluid and semi-fluid organic wastes and other impurities incidental to life and the occupation of such premises, and provision of a safe and adequate supply of gases for lighting, heating, and industrial purposes. Work permitted under this classification shall include the furnishing of materials, fixtures and labor to extend service from a building out to the main water, sewer or gas pipeline. The General Plumbing Contractor scope of practice does not include activities described in this Subsection under specialty classification S354-Radon Mitigation Contractor unless the work is performed under the immediate supervision of an employee who holds a current certificate issued by the National Radon Safety Board (NRSB) or the National Radon Proficiency Program ([NEHA]AARST-NRPP).

    S211 - Boiler Installation Contractor. Fabrication and/or installation of fire-tube and water-tube power boilers and hot water heating boilers, including all fittings and piping, valves, gauges, pumps, radiators, converters, fuel oil tanks, fuel lines, chimney flues, heat insulation and all other devices, apparatus, and equipment related thereto in a closed system not connected to the culinary water system. Notwithstanding the foregoing, where water delivery for the closed system is connected to the culinary water system and separated from the culinary water system by a backflow prevention device, a contractor licensed under this subsection may connect the closed system to the backflow prevention device, which must be installed by an actively licensed plumber.

    S212 - Irrigation Sprinkling Contractor. Layout, fabrication, and/or installation of water distribution system for artificial watering or irrigation.

    S213 - Industrial Piping Contractor. Fabrication and/or installation of pipes and piping for the conveyance or transmission of steam, gases, chemicals, and other substances including excavating, trenching, and back-filling related to such work. This classification includes the above work for geo thermal systems.

    S214 - Water Conditioning Equipment Contractor. Fabrication and/or installation of water conditioning equipment and only such pipe and fittings as are necessary for connecting the water conditioning equipment to the water supply system within the premises.

    S215 - Solar Thermal Systems Contractor. Construction, repair and/or installation of solar thermal systems up to the system shut off valve or where the system interfaces with any other plumbing system.

    S216 - Residential Sewer Connection and Septic Tank Contractor. Construction of residential sewer lines including connection to the public sewer line, and excavation and grading related thereto. Excavation, installation and grading of residential septic tanks and their drainage.

    S217 - Residential Plumbing Contractor. Fabrication and/or installation of material and fixtures to create and maintain sanitary conditions in residential building, including multiple units up to and including a four-plex by providing a permanent means for a supply of safe and pure water, a means for the timely and complete removal from the premises of all used or contaminated water, fluid and semi-fluid organic wastes and other impurities incidental to life and the occupation of such premises, and provision of a safe and adequate supply of gases for lighting and heating purposes. Work permitted under this classification shall include the furnishing of materials, fixtures and labor to extend service from a residential building out to the main water, sewer or gas pipeline. Excluded is any new construction and service work generally recognized in the industry as commercial or industrial.

    S220 - Carpentry Contractor. Fabrication for structural and finish purposes in a structure or building using wood, wood products, metal studs, vinyl materials, or other wood/plastic/metal composites as is by custom and usage accepted in the building industry as carpentry. Incidental work includes the installation of tub liners and wall systems.

    S221 - Cabinet, Millwork and Countertop Installation Contractor. On-site construction and/or installation of milled wood products or countertops.

    S222 - Overhead and Garage Door Contractor. The installation of overhead and garage doors and door openers.

    S230 - Siding Contractor. Fabrication, construction, and/or installation of siding.

    S231 - Raingutter Installation Contractor. On-site fabrication and/or installation of raingutters and drains, roof flashings, gravel stops and metal ridges.

    S240 - Glass and Glazing Contractor. Fabrication, construction, installation, and/or removal of all types and sizes of glass, mirrors, substitutes for glass, glass-holding members, frames, hardware, and other incidental related work.

    S250 - Insulation Contractor. Installation of any insulating media in buildings and structures for the sole purpose of temperature control, sound control or fireproofing, but shall not include mechanical insulation of pipes, ducts or conduits.

    S260 - General Concrete Contractor. Fabrication, construction, mixing, batching, and/or installation of concrete and related concrete products along with the placing and setting of screeds for pavement for flatwork, the construction of forms, placing and erection of steel bars for reinforcing and application of plaster and other cement-related products.

    S261 - Concrete Form Setting and Shoring Contractor. Fabrication, construction, and/or installation of forms and shoring material; but, does not include the placement of concrete, finishing of concrete or embedded items such as metal reinforcement bars or mesh.

    S262 - Gunnite and Pressure Grouting Contractor. Installation of a concrete product either injected or sprayed under pressure.

    S263 - Cementatious Coating Systems Resurfacing and Sealing Contractor. Fabrication, construction, mixing, batching and installation of cementatious coating systems or sealants limited to the resurfacing or sealing of existing surfaces, including the preparation or patching of the surface to be covered or sealed.

    S270 - General Drywall and Plastering Contractor. Fabrication, construction, and installation of drywall, gypsum, wallboard panels and assemblies. Preparation of drywall or plaster surfaces for suitable painting or finishing. Application to surfaces of coatings made of plaster, including the preparation of the surface and the provision of a base. This does not include applying stucco to lathe, plaster and other surfaces. Exempted is the plastering of foundations.

    S272 - Ceiling Grid Systems, Ceiling Tile and Panel Systems Contractor. Fabrication and/or installation of wood, mineral, fiber, and other types of ceiling tile and panels and the grid systems required for placement.

    S273 - Light-weight Metal and Non-bearing Wall Partitions Contractor. Fabrication and/or installation of light-weight metal and other non-bearing wall partitions.

    S280 - General Roofing Contractor. Application and/or installation of asphalt, pitch, tar, felt, flax, shakes, shingles, roof tile, slate, and any other material or materials, or any combination of any thereof which use and custom has established as usable for, or which are now used as, water-proof, weatherproof, or watertight seal or membranes for roofs and surfaces; and roof conversion. Incidental work includes the installation of roof clamp ring to the roof drain.

    S290 - General Masonry Contractor. Construction by cutting, and/or laying of all of the following brick, block, or forms: architectural, industrial, and refractory brick, all brick substitutes, clay and concrete blocks, terra-cotta, thin set or structural quarry tile, glazed structural tile, gypsum tile, glass block, clay tile, copings, natural stone, plastic refractories, and castables and any incidental works, including the installation of shower pans, as required in construction of the masonry work.

    S291 - Stone Masonry Contractor. Construction using natural or artificial stone, either rough or cut and dressed, laid at random, with or without mortar. Incidental work includes the installation of shower pans.

    S292 - Terrazzo Contractor. Construction by fabrication, grinding, and polishing of terrazzo by the setting of chips of marble, stone, or other material in an irregular pattern with the use of cement, polyester, epoxy or other common binders. Incidental work includes the installation of shower pans.

    S293 - Marble, Tile and Ceramic Contractor. Preparation, fabrication, construction, and installation of artificial marble, burned clay tile, ceramic, encaustic, falence, quarry, semi-vitreous, and other tile, excluding hollow or structural partition tile. Incidental work includes the installation of shower pans.

    S294 - Cultured Marble Contractor. Preparation, fabrication and installation of slab and sheet manmade synthetic products including cultured marble, onyx, granite, onice, corian, and corian type products. Incidental work includes the installation of shower pans.

    S300 - General Painting Contractor. Preparation of surface and/or the application of all paints, varnishes, shellacs, stains, waxes and other coatings or pigments.

    S310 - Excavation and Grading Contractor. Moving of the earth's surface or placing earthen materials on the earth's surface, by use of hand or power machinery and tools, including explosives, in any operation of cut, fill, excavation, grading, trenching, backfilling, or combination thereof as they are generally practiced in the construction trade.

    S320 - Steel Erection Contractor. Construction by fabrication, placing, and tying or welding of steel reinforcing bars or erecting structural steel shapes, plates of any profile, perimeter or cross-section that are used to reinforce concrete or as structural members, including riveting, welding, and rigging.

    S321 - Steel Reinforcing Contractor. Fabricating, placing, tying, or mechanically welding of reinforcing bars of any profile that are used to reinforce concrete buildings or structures.

    S322 - Metal Building Erection Contractor. Erection of pre-fabricated metal structures including concrete foundation and footings, grading, and surface preparation.

    S323 - Structural Stud Erection Contractor. Fabrication and installation of metal structural studs and bearing walls.

    S330 - Landscaping Contractor.

    (a) grading and preparing land for architectural, horticultural, or decorative treatment;

    (b) arrangement, and planting of gardens, lawns, shrubs, vines, bushes, trees, or other decorative vegetation;

    (c) construction of small decorative pools, tanks, fountains, hothouses, greenhouses, fences, walks, garden lighting of 50 volts or less, or sprinkler systems;

    (d) construction of retaining walls except retaining walls which are intended to hold vehicles, structures, equipment or other non natural fill materials within the area located within a 45 degree angle from the base of the retaining wall to the level of where the additional weight bearing vehicles, structures, equipment or other non natural fill materials are located; or

    (e) patio areas except that:

    (i) no decking designed to support humans or structures shall be included; and

    (ii) no concrete work designed to support structures to be placed upon the patio shall be included.

    (f) This classification does not include running electrical or gas lines to any appliance.

    S340 - Sheet Metal Contractor. Layout, fabrication, and installation of air handling and ventilating systems. All architectural sheet metal such as cornices, marquees, metal soffits, gutters, flashings, and skylights and skydomes including both plastic and fiberglass.

    S350 - HVAC Contractor. Fabrication and installation of complete warm air heating and air conditioning systems, and complete ventilating systems. The HVAC Contractor scope of practice does not include activities described in this Subsection under specialty classification S354-Radon Mitigation Contractor unless the work is performed under the immediate supervision of an employee who holds a current certificate issued by the National Radon Safety Board (NRSB) or the National Radon Proficiency Program ([NEHA]AARST-NRPP).

    S351 - Refrigerated Air Conditioning Contractor. Fabrication and installation of air conditioning ventilating systems to control air temperatures below 50 degrees.

    S352 - Evaporative Cooling Contractor. Fabrication and installation of devices, machinery, and units to cool the air temperature employing evaporation of liquid.

    S353 - Warm Air Heating Contractor. Layout, fabrication, and installation of such sheet metal, gas piping, and furnace equipment as necessary for a complete warm air heating and ventilating system.

    S354 - Radon Mitigation Contractor. Layout, fabrication, and installation of a radon mitigation system. This classification does not include work on heat recovery ventilation or makeup air components which must be performed by an HVAC Contractor and does not include electrical wiring which must be performed by an Electrical Contractor. Work performed under this classification shall be performed under the immediate supervision of an employee who holds a current certificate issued by the National Radon Safety Board (NRSB) or the National Radon Proficiency Program ([NEHA]AARST-NRPP).

    S360 - Refrigeration Contractor. Construction and/or installation of refrigeration equipment including, but not limited to, built-in refrigerators, refrigerated rooms, insulated refrigerated spaces and equipment related thereto; but, the scope of permitted work does not include the installation of gas fuel or electric power services other than connection of electrical devices to a junction box provided for that device and electrical control circuitry not exceeding 50 volts.

    S370 - Fire Suppression Systems Contractor. Layout, fabrication, and installation of fire protection systems using water, steam, gas, or chemicals. When a potable sanitary water supply system is used as the source of supply, connection to the water system must be accomplished by a licensed plumbing contractor. Excluded from this classification are persons engaged in the installation of fire suppression systems in hoods above cooking appliances.

    S380 - Swimming Pool and Spa Contractor. On-site fabrication, construction and installation of swimming pools, prefabricated pools, spas, and tubs.

    S390 - Sewer and Waste Water Pipeline Contractor. Construction of sewer lines, sewage disposal and sewage drain facilities including excavation and grading with respect thereto, and the construction of sewage disposal plants and appurtenances thereto.

    S400 - Asphalt Paving Contractor. Construction of asphalt highways, roadways, driveways, parking lots or other asphalt surfaces, which will include but will not be limited to, asphalt overlay, chip seal, fog seal and rejuvenation, micro surfacing, plant mix sealcoat, slurry seal, and the removal of asphalt surfaces by milling. Also included is the excavation, grading, compacting and laying of fill or base-related thereto. Also included in painting on asphalt surfaces including striping, directional and other types of symbols or words.

    S410 - Pipeline and Conduit Contractor. Fabrication, construction, and installation of pipes, conduit or cables for the conveyance and transmission from one station to another of such products as water, steam, gases, chemicals, slurries, data or communications. Included are the excavation, cabling, horizontal boring, grading, and backfilling necessary for construction of the system.

    S420 - General Fencing, Ornamental Iron and Guardrail Contractor. Fabrication, construction, and installation of fences, guardrails, handrails, and barriers.

    S421 - Residential Fencing Contractor. Fabrication and installation of residential fencing up to and including a height of six feet.

    S430 - Metal Firebox and Fuel Burning Stove Installer. Fabrication, construction, and installation of metal fireboxes, fireplaces, and wood or coal-burning stoves, including the installation of venting and exhaust systems, provided the individual performing the installation is RMGA certified.

    S440 - Sign Installation Contractor. Installation of signs and graphic displays which require installation permits or permission as issued by state or local governmental jurisdictions. Signs and graphic displays shall include signs of all types, both lighted and unlighted, permanent highway marker signs, illuminated awnings, electronic message centers, sculptures or graphic representations including logos and trademarks intended to identify or advertise the user or his product, building trim or lighting with neon or decorative fixtures, or any other animated, moving or stationary device used for advertising or identification purposes. Signs and graphic displays must be fabricated, installed and erected in accordance with professionally engineered specifications and wiring in accordance with the National Electrical Code.

    S441 - Non Electrical Outdoor Advertising Sign Contractor. Installation of signs and graphic displays which require installation permits or permission as issued by state and local governmental jurisdictions. Signs and graphics shall include outdoor advertising signs which do not have electrical lighting or other electrical requirements, and in accordance with professionally engineered specifications.

    S450 - Mechanical Insulation Contractor. Fabrication, application and installation of insulation materials to pipes, ducts and conduits.

    S460 - Wrecking and Demolition Contractor. The raising, cribbing, underpinning, moving, and removal of building and structures.

    S470 - Petroleum Systems Contractor. Installation of above and below ground petroleum and petro-chemical storage tanks, piping, dispensing equipment, monitoring equipment and associated petroleum and petro-chemical equipment including excavation, backfilling, concrete and asphalt.

    S480 - Piers and Foundations Contractor. The excavation, drilling, compacting, pumping, sealing and other work necessary to construct, alter or repair piers, piles, footings and foundations placed in the earth's subsurface to prevent structural settling and to provide an adequate capacity to sustain or transmit the structural load to the soil or rock below.

    S490 - Wood Flooring Contractor. Installation of wood flooring including prefinished and unfinished material, sanding, staining and finishing of new and existing wood flooring. Underlayments, non-structural subfloors and other incidental related work.

    S491 - Laminate Floor Installation Contractor. Installation of laminate floors including underlayments, non-structural subfloors and other incidental related work, but does not include the installation of sold wood flooring.

    S500 - Sports and Athletic Courts, Running Tracks, and Playground Installation Contractor. Installation of sports and athletic courts including but not limited to tennis courts, racquetball courts, handball courts, basketball courts, running tracks, playgrounds, or any combination. Includes nonstructural floor subsurfaces, nonstructural wall surfaces, perimeter walls and perimeter fencing. Includes the installation and attachment of equipment such as poles, basketball standards or other equipment.

    S510 - Elevator Contractor. Erecting, constructing, installing, altering, servicing, repairing or maintaining an elevator.

    S600 - General Stucco Contractor. Applying stucco to lathe, plaster and other surfaces.

    S700 - Specialty License Contractor.

    (a) A specialty license is a license that confines the scope of the allowable contracting work to a specialized area of construction which the Division grants on a case-by-case basis.

    (b) When applying for a specialty license, an applicant, if requested, shall submit to the Division the following:

    (i) a detailed statement of the type and scope of contracting work that the applicant proposes to perform; and

    (ii) any brochures, catalogs, photographs, diagrams, or other material to further clarify the scope of the work that the applicant proposes to perform.

    (c) A contractor issued a specialty license shall confine the contractor's activities to the field and scope of operations as outlined by the Division.

    (3) The scope of practice for the following primary classifications includes the scope of practice stated in the descriptions for the following subsclassifications:

     

    TABLE I

     
         Primary Classification     Included subclassifications
              S200                  S201, S202
              S210                  S211, S212, S213, S214, S215,
                                     S216, S217
              S220                  S221, S222
              S230                  S231
              S260                  S261, S262, S263
              S270                  S272, S273
              S290                  S291, S292, S293, S294
              S320                  S321, S322, S323
              S350                  S351, S352, S353, S354
              S420                  S421
              S440                  S441
              S490                  S491

     

    (4) The following activities are determined to not significantly impact the public health, safety and welfare and therefore do not require a contractors license:

    (a) sandblasting;

    (b) pumping services;

    (c) tree stump or tree removal;

    (d) installation within a building of communication cables including phone and cable television;

    (e) installation of low voltage electrical as described in R156-55b-102(1);

    (f) construction of utility sheds, gazebos or other similar items which are personal property and not attached;

    (g) building and window washing, including power washing;

    (h) central vacuum systems installation;

    (i) concrete cutting;

    (j) interior decorating;

    (k) wall paper hanging;

    (l) drapery and blind installation;

    (m) welding on personal property which is not attached;

    (n) chimney sweepers other than repairing masonry;

    (o) carpet and vinyl floor installation;

    (p) artificial turf installation;

    (q) general cleanup of a construction site which does not include demolition or excavation; and

    (r) work that would otherwise be limited to individuals holding the S260, S261, S262, S263, S290, S310, S330, S380, S420, S421 and S500 specialty classifications if the work is within the $1,000 or $3,000 labor and material limit as specified in the handyman exemption in Subsection 58-55-305(1)(h).

    (5) The following activities are those determined to not significantly impact the public health, safety and welfare beyond the regulations by other agencies and therefore do not require a contractors license:

    (a) lead removal regulated by the Department of Environmental Quality;

    (b) asbestos removal regulated by the Department of Environmental Quality; and

    (c) fire alarm installation regulated by the Fire Marshal.

     

    R156-55a-302b. Qualifications for Licensure - Experience Requirements.

    In accordance with Subsection 58-55-302(1)(e)(ii), the minimum experience requirements are established as follows:

    (1) Requirements for all license classifications:

    (a) Unless otherwise provided in this rule, two years of experience shall be lawfully performed within the 10-year period preceding the date of application under the general supervision of a contractor, and shall be subject to the following:

    (i) If the experience was completed in Utah, it shall be:

    (A) completed while a W-2 employee of a licensed contractor; or

    (B) completed while working as an owner of a licensed contractor, which has for all periods of experience claimed, employed a qualifier who performed the duties and served in the capacities specified in Subsection 58-55-304(4) and in Subsection R156-55a-304.

    (ii) If the experience was completed outside of the state of Utah, it shall be:

    (A) completed in compliance with the laws of the jurisdiction in which the experience is completed; and

    (B) completed with supervision that is substantially equivalent to the supervision that is required in Utah.

    (iii) Experience may be determined to be substantially equivalent if lawfully obtained in a setting which has supervision of qualified persons and an equivalent scope of work, such as performing construction activities in the military where licensure is not required.

    (b) One year of work experience means 2000 hours.

    (c) No more than 2000 hours of experience during any 12 month period may be claimed.

    (d) Except as described in Subsection (2)b, experience obtained under the supervision of a construction trades instructor as a part of an educational program is not qualifying experience for a contractors license.

    (e) If the applicant's qualifying experience is outdated but has previously been approved in the state of Utah, a passing score on the trade examination and the laws and rules examination obtained within the one-year period preceding the date of application will requalify the applicant's experience.

    (2) Requirements for E100 General Engineering, B100 General Building, R100 Residential and Small Commercial Building license classifications:

    (a) One of the required two years of experience shall be in a supervisory or managerial position.

    (b) A person holding a [four year]four-year bachelors degree or a [two year]two-year associates degree in Construction Management may have one year of experience credited towards the supervisory or managerial experience requirement.

    (c) A person holding a Utah professional engineer license may be credited with satisfying one year toward the supervisory or managerial experience required for E100 contractor license.

    (3) Requirements for I101 General Engineering Trades Instruction Facility, I102 General Building Trades Instruction Facility, I103 Electrical Trades Instruction Facility, I104 Plumbing Trades Instruction Facility, I105 Mechanical Trades Instruction Facility license classifications:

    An applicant for construction trades instruction facility license shall have the same experience that is required for the license classifications for the construction trade they will instruct.

    (4) Requirements for S202 Solar Photovoltaic Contractor. In addition to the requirements of Subsection (1), an applicant shall hold a current certificate by the North American Board of Certified Energy Practitioners.

    (5) Requirements for S354 Radon Mitigation Contractor. In addition to the requirements of Subsection (1), an applicant shall hold a current certificate issued by the National Radon Safety Board (NRSB) or the National Radon Proficiency Program ([NEHA]AARST-NRPP). Experience completed prior to the effective date of this rule does not need to be performed under the supervision of a licensed contractor. Experience completed after the effective date of this rule must be performed under the supervision of a licensed contractor who has authority to practice radon mitigation.

     

    R156-55a-303b. Continuing Education - Standards.

    (1) Required Hours. Pursuant to Subsection 58-55-302.5, each licensee shall complete a total of six hours of continuing education during each two year license term. A minimum of three hours shall be core education. The remaining three hours are to be professional education. Additional core education hours beyond the required amount may be substituted for professional education hours. A minimum of three hours shall consist of live in-class attendance. The remaining three hours may consist of courses provided through distance learning.

    (a) "Core continuing education" is defined as construction codes, construction laws, job site safety, OSHA 10 or OSHA 30 safety training, governmental regulations pertaining to the construction trades and employee verification and payment practices, finance , [and ]bookkeeping , and construction business practices.

    (b) "Professional continuing education" is defined as substantive subjects dealing with the practice of the construction trades, including land development, land use, planning and zoning, energy conservation, professional development, arbitration practices, estimating, marketing techniques, servicing clients, personal and property protection for the licensee and the licensee's clients and similar topics.

    (c) The following course subject matter is not acceptable as core education or professional education hours: mechanical office and business skills, such as typing, speed reading, memory improvement and report writing; physical well-being or personal development, such as personal and business motivation, stress management, time management, dress for success, or similar subjects; presentations by a supplier or a supplier representative to promote a particular product or line of products; and meetings held in conjunction with the general business of the licensee or employer.

    (d) The Division may defer or waive the continuing education requirements as provided in Section R156-1-308d.

    (2) A continuing education course shall meet the following standards:

    (a) Time. Each hour of continuing education course credit shall consist of 50 minutes of education in the form of seminars, lectures, conferences, training sessions or distance learning modules. The remaining ten minutes is to allow for breaks.

    (b) Provider. The course provider shall be among those specified in Subsection 58-55-302.5(2).

    (c) Content. The content of the course shall be relevant to the practice of the construction trades and consistent with the laws and rules of this state.

    (d) Objectives. The learning objectives of the course shall be reasonably and clearly stated.

    (e) Teaching Methods. The course shall be presented in a competent, well organized and sequential manner consistent with the stated purpose and objective of the program.

    (f) Faculty. The course shall be prepared and presented by individuals who are qualified by education, training and experience.

    (g) Distance learning. A course that is provided through Internet or home study may be recognized for continuing education if the course verifies registration and participation in the course by means of a test demonstrating that the participant has learned the material presented. Test questions shall be randomized for each participant. A home study course shall include no fewer than five variations of the final examination, distributed randomly to participants. Home study courses, including the five exam variations, shall be submitted in their entirety to the Division for review. Providers shall track the following:

    (i) the amount of time each student has spent in the course;

    (ii) what activities the student did or did not access; and

    (iii) all of the student's test scores.

    (h) Documentation. The course provider shall have a competent method of registration of individuals who actually completed the course, shall maintain records of attendance that are available for review by the Division and shall provide individuals completing the course a certificate that contains the following information:

    (i) the date of the course;

    (ii) the name of the course provider;

    (iii) the name of the instructor;

    (iv) the course title;

    (v) the hours of continuing education credit and type of credit (core or professional);

    (vi) the attendee's name; and

    (v) the signature of the course provider.

    (i) Live Broadcast. A course provided through live broadcast may be recognized for live in-class continuing education credit if the student and the instructor are able to see and hear each other.

    (3) On a random basis, the Division may assign monitors at no charge to attend a course for the purpose of evaluating the course and the instructor.

    (4) Each licensee shall maintain adequate documentation as proof of compliance with this section, such as certificates of completion, course handouts and materials. The licensee shall retain this proof for a period of three years from the end of the renewal period for which the continuing education is due. Each licensee shall assure that the course provider has submitted the verification of attendance to the continuing education registry on behalf of the licensee as specified in Subsection (8). Alternatively, the licensee may submit the course for approval and pay any course approval fees and attendance recording fees.

    (5) Licensees who lecture in continuing education courses meeting these requirements shall receive two hours of continuing education for each hour spent lecturing. However, no lecturing or teaching credit is available for participation in a panel discussion.

    (6) The continuing education requirement for electricians, plumbers and elevator mechanics as established in Subsections 58-55-302.7, if offered by a provider specified in Subsection 58-55-302.5(2), shall satisfy the continuing education requirement for contractors as established in Subsection 58-55-302.5 and implemented herein. The contractor licensee shall assure that the course provider has submitted the verification of the electrician's, plumber's or elevator mechanic's attendance on behalf of the licensee to the continuing education registry as specified in Subsection (8).

    (7) A course provider shall submit continuing education courses to the continuing education registry and shall submit verification of attendance and completion on behalf of licensees attending and completing the program directly to the continuing education registry in the format required by the continuing education registry.

    (8) The Division shall review continuing education courses which have been submitted through the continuing education registry and approve only those courses which meet the standards set forth under this Section.

    (9) As provided in Section 58-1-401 and Subsections 58-55-302.5(2) and 58-55-302.7(4)(a), the Division may refuse to renew or may revoke, suspend, restrict, place on probation, issue a public reprimand to, or otherwise act upon the approval of any course or provider, if the course or provider fails to meet any of the requirements of this section or the provider has engaged in unlawful or unprofessional conduct.

    (10) Continuing Education Registry.

    (a) The Division shall designate an entity to act as the Continuing Education Registry under this rule.

    (b) The Continuing Education Registry, in consultation with the Division and the Commission, shall:

    (i) through its internet site electronically receive applications from continuing education course providers and shall submit the application for course approval to the Division for review and approval of only those programs that meet the standards set forth under this Section;

    (ii) publish on their website listings of continuing education programs that have been approved by the Division, and which meet the standards for continuing education credit under this rule;

    (iii) maintain accurate records of qualified continuing education approved;

    (iv) maintain accurate records of verification of attendance and completion, by individual licensee, which the licensee may review for compliance with this rule; and

    (v) make records of approved continuing education programs and attendance and completion available for audit by representatives of the Division.

    (c) Fees. A continuing education registry may charge a reasonable fee to continuing education providers or licensees for services provided for review and approval of continuing education programs.

     

    KEY: contractors, occupational licensing, licensing

    Date of Enactment or Last Substantive Amendment: [June 21, 2016]2017

    Notice of Continuation: August 4, 2016

    Authorizing, and Implemented or Interpreted Law: 58-1-106(1)(a); 58-1-202(1)(a); 58-55-101; 58-55-308(1)(a); 58-55-102(39)(a)


Document Information

Hearing Meeting:
04/26/2017 09:15 AM, Heber Wells Bldg, 160 E 300 S, Conference Room 474, Salt Lake City, UT
Effective Date:
5/8/2017
Publication Date:
04/01/2017
Type:
Notices of Proposed Rules
Filed Date:
03/07/2017
Agencies:
Commerce, Occupational and Professional Licensing
Rulemaking Authority:

Subsection 58-1-106(1)(a)

Section 58-55-101

Subsection 58-55-102(39)(a)

Subsection 58-1-202(1)(a)

Subsection 58-55-308(1)(a)

Authorized By:
Mark Steinagel, Director
DAR File No.:
41348
Summary:
In Subsections R156-55a-301(2) and R156-55a-302b(5), the proposed amendment is a technical change of name for the National Radon Proficiency Program from NEHA-NRPP to AARST-NRPP. The entity has changed the name of the certificate it issues. In Subsection R156-55a-303b(1)(a), the proposed amendment adds construction business practices to the list of courses that qualify as core continuing education. New Section R156-55a-303b(2)(i) allows live continuing education courses to be taught by live ...
CodeNo:
R156-55a
CodeName:
{30863|R156-55a|R156-55a. Utah Construction Trades Licensing Act Rule}
Link Address:
CommerceOccupational and Professional LicensingHEBER M WELLS BLDG160 E 300 SSALT LAKE CITY, UT 84111-2316
Link Way:

Chris Rogers, by phone at 801-530-6720, by FAX at 801-530-6511, or by Internet E-mail at crogers@utah.gov

AdditionalInfo:
More information about a Notice of Proposed Rule is available online. The Portable Document Format (PDF) version of the Bulletin is the official version. The PDF version of this issue is available at https://rules.utah.gov/publicat/bull_pdf/2017/b20170401.pdf. The HTML edition of the Bulletin is a convenience copy. Any discrepancy between the PDF version and HTML version is resolved in favor of the PDF version. Text to be deleted is struck through and surrounded by brackets ([example]). Text ...
Related Chapter/Rule NO.: (1)
R156-55a. Utah Construction Trades Licensing Act Rules.